cycleCount used to tick once per instruction, so RSTA cost what SETD cost and a
CALL moving ten bytes of Stack cost what a branch cost. No machine anybody could
build works that way, and the emulator's job is to be the thing the hardware is
designed against.
Every touch of memory now goes through one of four accessors that charge for it:
fetching an opcode, fetching the bytes after it, reading or writing Data Memory,
and reaching a device port. One access, one cycle, nothing overlapped. The
accessors exist so the cost is counted where the access happens rather than in a
table of per instruction costs kept somewhere else - a table like that is a
second copy of what the code does, and the two drift.
The run loop spends a budget of cycles instead of running a count of
instructions, so the emulated rate means something: an instruction costs what it
touches, and a batch ends when the cycles are gone.
What the numbers say now: RSTA 1 and SETD 4, being one byte and four. LDA 3,
DPUA 2. CALL and RET together 24, RCAL and RRET together 8, because the first
pair moves twenty bytes of Stack and the second moves four. The average SplitBit
instruction costs 3.72 of these, measured over the native assembler assembling a
program.
And the measurement that prompted all of this: converting the filesystem's
hottest leaf routine to RCAL is 3.1 per cent cheaper on a directory heavy
workload. The old model said 0.0, which is what a model that cannot see memory
traffic must say about a change that is nothing else.
Three tests moved. settle() strips the cycle count from recorded output, so
nothing should have churned - but it was anchored to the start of a line and
replCalculator's last output has no newline on it, which leaves the halt message
mid line where the pattern never reached. Not anchored any more.
The two Life programs are bounded by a cycle count because they never end, and
that number was rescaled from 3,000,000 to 11,200,000 - the same amount of work
at 3.72 cycles to the instruction. Nothing about either program changed. No limit
reproduces the old output exactly, because the cut now lands elsewhere in a
frame, so they are recorded again rather than tuned to match.
Whether hardware overlaps a fetch with the end of the previous instruction is
left open on purpose. This is the conservative model; pipelining is a decision to
make while drawing the hardware, not one to inherit from an emulator.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01E2JrLzFvuFX9fgi1LDRjrW
The six settled back on the twenty fourth, built now.
RCAL and RRET are a call that puts nothing back. CALL restores A, B and Data
Pointers 0 through 2, which costs ten bytes of Stack and is why a subroutine
here can only hand anything back through Q, DP3 or memory. RCAL costs two and
restores nothing, which is what a short leaf routine wants and is unsafe in
exactly the way the name says.
They are a pair because the frames are different sizes: returning from one
through the other walks the Stack to somewhere that was never a return address.
That was the user's correction to the original proposal, which had a raw call
and no raw return.
DPUA and DPDA offset a Data Pointer by A; DPUW and DPDW by A and B together,
most significant first. DPUP and DPDN take a byte written into the program, so
moving a pointer by something just worked out meant storing it and loading it
back. Down as well as up on symmetry grounds, which was also the user's call -
the argument against it came from counting uses in a corpus written under the
constraint.
The opcodes sit where they belong: 0x16 and 0x1E immediately below CALL and RET,
and 0x4E through 0x51 at the end of the Data Pointer family. All six fit shapes
that already existed, so instructiontable.py needed only set membership and both
machine side copies of the table regenerated from it unchanged.
Checked at every level it exists at: the emulator runs them, the host assembler
encodes them, the monitor disassembles all six with the right lengths, and the
assembler that runs on the machine builds a program using them byte for byte
identically to the host - and that program runs.
The recorded test measures what the two calls COST as well as what they put
back, because an RCAL that quietly did what CALL does would still return to the
right place. It does not survive that: returned through RRET, it hangs.
docs.sh can read a two word number now. The count of instructions taking a Data
Pointer went past twenty, and the pattern only allowed one word, so the check
would have reported that the manual had stopped saying it rather than that the
number was wrong.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01E2JrLzFvuFX9fgi1LDRjrW
"Binary" was doing three jobs. It meant an SPBT file that the machine starts
from; it meant whatever the assembler happened to produce, which is now
either that or a loadable program; and it meant a compiled host tool. A word
that means three things means none of them, and the first of the three has a
name already - this project has been calling them boot images for a while
and the manuals had not caught up.
Where it means an SPBT file -> boot image
Where it means either output -> output
Where it means a host executable -> left alone
Where it means base two -> left alone
The user facing messages move with it:
Error: No boot image specified.
Usage: ./SplitBit [OPTIONS] <boot image>
Error: This is not a SplitBit boot image.
Error: This boot image is in format version 2, and this emulator reads 1.
Successfully wrote SplitBit boot image to "hello.bin".
The assembler's own help was the interesting case. Its -o writes either
format, so "the binary" there was never right - it is "the output" now, and
the message that names the format is the one that says which it wrote.
No recorded output contained the word, so nothing needed re-blessing.
Checked before starting rather than after.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01E2JrLzFvuFX9fgi1LDRjrW
Overflowing/Underflowing A or B with increment or decrement instructions now sets the Carry Flag.
An increment or decrement of A or B that doesn't result in an overflow/underflow now clears the Carry Flag.
Q is no longer saved and restored in subroutine calls, allowing it to be used to return a one byte result.
Documentation updated with more detail.
Added DPUP and DPDN, which take a one byte operand specifying how far up or down to offset the Data Pointer.
Three Fibonacci generators using the print.asm library.
- 8 bit values printing in decimal representation.
- 16 bit values printing in hexadecimal representation.
- 32 bit values printing in hexadecimal representation.
AnachronautandClaude Opus 5
Anachronaut